The DYS F4 PRO V2 is a high performance Flight Controller designed for FPV hobbyists. DYS F4 PRO V2 not only combines the PDB board with the flight controller, but also has an integrated OSD, current meter, voltmeter and built-in high power BEC. It is integrated with an OSD and Current Sensor, so you don't need to flash firmware, and you can debug OSD via a BF ground station. You also can adjust t..

The best selling Micro Swift 2 just got better. The RunCam Micro Swift 3 now comes with a full-size lens and built-in RunCam control adapter. Control your FPV camera remotely with the built-in UART camera control technology and never use a menu cable again. RunCam has replaced the GND and OSD pins on the camera with TX and RX pins allowing you to wire your camera directly to your flight ..

DYS F20A 20amp 4 in 1 BLHeli_S ESC 2-4S. BB2 BEC 5V/12V 3A. Supports Dshot600, Oneshot125, Oneshot42, Multishot.Specifications:Continuous current: 20A, Burst Current: 25A up to 10SInput voltage: 2-4s LipoBEC output: 5V/12  3ASize (mm) L*W*H: 36*36*8Type: BLHeli_S FirmwareWeight: 12.5g (excluding cable and connector)Firmware: BLHeli_SSupports Dshot150/300/600, Oneshot125/42, Multishot, PWMMain..

DYS F30A 30amp 4 in 1 BLHeli_S ESC 2-4S. BB2 BEC 5V/12V 3A. Supports Dshot600, Oneshot125, Oneshot42, Multishot.Specifications:Continuous Current: 30A, Burst Current: 35AInput Voltage: 2-6S LipoBEC Output: 5V/3A, 12V/1A (only applies to 4S, 5S, 6S, 12V/1A)Size: 43*40*8mmWeight: 12.95gFirmware: BLHeli_SSupports: Dshot150/300/600, Oneshot125/42, Multishot, PWMMain IC: EMF8BB21F16G SILABS, 8bit C8051..

The DYS F4 Pro Flight Controller uses the OMNIBUSF4 firmware. It is integrated with OSD and Current Sensor, so you don't need to flash firmware, and you can debug OSD via BF ground station. You also can adjust the PID by OSD via remote control. The integrated current sensor can monitor the real-time power consumption. This DYS F4 Pro Flight Controller is compatible with all ESCs, as well as DYS 4-..

DYS racing Fire motor is the new stage of motor with 0.1mm laminations, imported ISC bearings and N54 magnets. The motor weighs only 32g with motor wire, and has an M5 hollow shaft.Specifications:KV: 2300Configuration: NPStator Diameter: 22.0mmStator Length: 6.0mmShaft Diameter: 3.0mmMotor Dimensions (Dia*Len): 27.7x17.7mmWeight: 32gNo.of Cells (Lipo): 3-4SMax Continuous current(A): 31.7AMax Conti..

DYS racing Fire motor is the new stage of motor with 0.1mm laminations, imported ISC bearings and N54 magnets. The motor weighs only 32g with motor wire, and has an M5 hollow shaft.Specifications:KV: 2600Configuration: NPStator Diameter: 22.0mmStator Length: 6.0mmShaft Diameter: 3.0mmMotor Dimensions (Dia*Len): 27.7x17.7mmWeight: 32gNo.of Cells (Lipo): 3-4SMax Continuous current(A): 34.8AMax Conti..

DYS just released their latest motor: The Mars. Mars size is 2306 and is available in 2400KV and 2750KV variants.Specifications:KV: 2400Configuration: NPStator Diameter: 23.0mmStator Length: 6.0mmShaft Diameter: M5Motor Dimensions (Dia*Len): 28.5x18.7mmWeight: 34.4gNo.of Cells (Lipo): 3-6SMax Continuous current(A): 34.5AMax Continuous Power(W): 574.4WInternal resistance: 0.04Includes:1 x DYS Mars ..

DYS just released their latest motor: The Mars. Mars size is 2306 and is available in 2400KV and 2750KV variants.Specifications:KV: 2750Configuration: NPStator Diameter: 23.0mmStator Length: 6.0mmShaft Diameter: M5Motor Dimensions (Dia*Len): 28.5x18.7mmWeight: 34.4gNo.of Cells (Lipo): 3-6SMax Continuous current(A): 40.4AMax Continuous Power(W): 646.4WInternal resistance: 0.04Includes:1 x DYS Mars ..

DYS SE PRO 2205 2300kV motor features 0.20 laminations, a screw to secure the motor shaft in place as well as individual solder tabs, making it easy to re-use the motors on different builds. Specifications:KV: 2300Configuration: NPStator Diameter: 22.0mmStator Length: 5.0mmShaft Diameter: M5Motor Dimensions (Dia*Len): 27.7x19.0mmWeight: 30.0gNo.of Cells (Lipo): 3-5SMax Continuous current(A): 26.8A..

DYS SE PRO 2205 2550kV motor features 0.20 laminations, a screw to secure the motor shaft in place as well as individual solder tabs, making it easy to re-use the motors on different builds. Specifications:KV: 2550Configuration: NPStator Diameter: 22.0mmStator Length: 5.0mmShaft Diameter: M5Motor Dimensions (Dia*Len): 27.7x19.0mmWeight: 30.0gNo.of Cells (Lipo): 3-5SMax Continuous current(A): 27.8A..

The EMAX 2306 series of motors offer some of the highest levels of quality and performance in a motor to date. Boasting incredible thrust numbers, with a perfect blend of efficiency, showcases how EMAX is a leader within the FPV community and delivering products that continuously challenge the market with bold new designs.Features:Low ProfileModified Cooling FinsCurved MagnetsUpdated BearingsHighe..

The EMAX 2306 series of motors offer some of the highest levels of quality and performance in a motor to date. Boasting incredible thrust numbers, with a perfect blend of efficiency, showcases how EMAX is a leader within the FPV community and delivering products that continuously challenge the market with bold new designs.Features:Low ProfileModified Cooling FinsCurved MagnetsUpdated BearingsHighe..

The market's lightest and smallest ESC, designed specifically for high-level FPV racing. Utilizing the latest BLHeli-S firmware (16.5) and hardware. PWM generates a signal to boost smoother throttle response and reduce noise.Supports new digital signal: DSHOT, and analog signals: MULTISHOT, ONESHOT42, ONESHOT125. Top quality MOSFET, ceramic capacitors. 3oz high TG PCB board, significantly improves..

Brand new Bullet Series (purple), super-mini, ultra-light ESC. BLHeli-S firmware/ supports DSHOT, MULTISHOT, ONESHOT42, ONESHOT125. New heat sink design both effectively reduces the core temperature, and avoids propeller strike damage. Imported MOS tube, Japanese ceramic capacitors, 3oz High-TG PCB board, significantly reduces electrical heat soak and improves system efficiency.Specifications:Cont..

The completely redesigned RS2205-S is upgraded with features racing multirotors absolutely need. The motor is lighter, yields faster bell rotational response, higher thrust, uses premium materials and backed with EMAX's legendary production quality. Lighter and Lower Profile2 grams lighter than the first version of the RS2205, the RS2205-S is a 2205 motor which has been overhauled for the weight c..

The completely redesigned RS2205-S is upgraded with features racing multirotors absolutely need. The motor is lighter, yields faster bell rotational response, higher thrust, uses premium materials and backed with EMAX's legendary production quality. Lighter and Lower Profile2 grams lighter than the first version of the RS2205, the RS2205-S is a 2205 motor which has been overhauled for the weight c..

Foxeer 40CH TM200 pigtail 200mW VTX with race band is designed for FPV racing, has DC7~24V input voltage and DC5V output.Specifications:Transmitter Frequency(MHz): Wideband FM ModulateVideo Format: NTSC/PALOutput Impedance: 50 OhmOutput Power: 200mWInput Voltage: 7-24VOperating Temperature: -10 to 85°CVideo Band Width: 0 - 8.0 MHzAudio carrier Frequency: 6.5 MHzVideo Input Level: 0.8 - 1.2 Vp-pAud..

The Lumenier LUX V2 flight controller is the next generation of the popular Lumenier LUX. It uses a powerful F3 processor along with top of the line hardware. Unleash the capabilities of your FPV Racing Quadcopter with the Lumenier LUX Flight Controller. Achieve gyro refresh rates up to 8kHz (high speed SPI) using popular Betaflight, CleanFlight and RaceFlight firmware along with ultra low looptim..